New Products

The exact definition of the state of stress is a basic requirement for determining material parameters for strength calculations. In uniaxial static or cyclic tests, no superimposed bending moment should occur in addition to the axial force.

Within the scope of research and development, not only standardized samples are tested, but also parts and components. Especially in the case of component testing, the test specimens can often have very different sizes. This presents the testing technology with a challenge in order to have the necessary test space available when the piston stroke is available.

The University of Luxembourg has been building a new site for teaching an research on the site of a former blast furnace. The Department of Engineering (DoE) is an interdisciplinary faculty working in the classic fields of civil engineering, electrical engineering, mechanical engineering and geophysics. The focus of the research lies in the development of technological solutions, the sustainable and economical use of resources of all kinds.

A good idea, further thought: The previous controller DIGIMAXX ® C 20 is replaced by the new digital measuring and control electronics DIGIMAXX® C-40. FORM+TEST thus offers a digital independent control system of the latest device platform. It is characterized by a high degree of accuracy and reproducibility of the test results. Even under adverse conditions (dust/dirt) easy to operate via a capacitive and robust touch display

With the UP 500, Form+Test supports material research of new materials at a renowned Russian university. The test machine was designed according to the customer's requirements in terms of machine frames and machine performance. Samples and even entire components can be tested at up to 10 Hz and 500 kN at up to 500°C. The climate chamber can be easily moved into and out of the rehearsal room. To ensure that the machine itself stays cool, the load strand is equipped with a separate cooling circuit. Simply a turn-key solution by FORM+TEST.

For sustainable building, wood is becoming increasingly important as a material for structural components. However, this requires that the material behaviour in the design is known and can be represented by suitable models. Due to the anisotropic structure, experimental investigations are necessary to create the model. However, due to the material characteristics, this can be a challenging task for testing technology. But the test systems from FORM + TEST will make an important contribution to this.

In response to the increasing degree of automation in testing technology, FORM+TEST Seidner&Co. GmbH offers a comprehensive solution for the rational testing of concrete specimens. This is offered in 2 automation levels by means of a measuring and weighing station. This gives the testing laboratory a solution for the future that scores points in terms of cost-effectiveness.

FORM+TEST Seidner&Co. GmbH has developed 2 series of TORSIONSPRÜFZYLINDERN to extend the product range of system components for torsion loading. These drives are used for defined torsion loading of test specimens for static and dynamic material and component testing.

Modular testing machine for demanding static and dynamic tests in research and development and quality control. The solid test frame with two columns ensures a high flexibility of adaption and fixing options.

The ACO brand worldwide stands for the uncompromising quality and performance commitment of the ACO Group. One of their core business activities is drainage. The construction, protection and preservation of traffic routes is an important future topic and is one of the big infrastructural challenges worldwide. ACO solutions guarantee maximum security on traffic areas and industrial territories. Gutters, gratings, drainages and manhole covers from ACO are designed for extreme loads and special installation conditions. ACO sets standards in quality, innovation and safety, shapes the standardization and even goes beyond.

An universal test frame with a maximum load of 160 kN for testing structural elements and components was shipped in January 2015.

Successful commissioning of a test frame with a nominal load of 250 kN. Due to the height-adjustable, pivoted cross-head individual test-bench setups can be easily realized.

Flexural device for testing concrete beams according to ASTM C78. Suitable for testing machines DELTA 5 and DELTA 6. Flexural device can be built-in into the existing testing machine.

BROSA AG is manufacturer of high-quality sensors for force measurement. The BROSA force measuring elements are constructed and manufactured acc. to different, partially patented, configuration concepts - depending on application-specific requirements. High measurement accuracies are guaranteed in the long term due to the consideration of the exact installation situation from the construction up to the calibration of the sensors.

The EM testing systems provide professional solutions for static and quasi-static testing tasks. The system is driven by a powerful, digitally controlled electromechanical drive with backlash-free preloaded ball screws.